Band Saw Blades for Structural Steel
We offer a wide range of Band Saw Blades. The band saw blades below are designed exclusively for cutting structural steel.
-
Highest grade high speed steel circular saw blade capable of cutting a wide variety of materials.
Edge material specifications
HSS edge material with high toughness is coated with TiAl (titanium aluminide).Target materials
Demonstrates high speed cutting and excellent durability for high tensile strength steel pipes. -
Circular saw blade suitable for cutting structural steel pipes.
Edge material specifications
Uses cermet tips with excellent wear resistance and deposition resistance.Target materials
Circular saw blade with the number of teeth increased for stably cutting thin-walled pipes. -
Coated circular saw blade for cutting stainless steel materials, characterized by high wear resistance.
Edge material specifications
Carbide tips with high toughness is coated original.Target materials
Excellent in deposition resistance and wear resistance suited, and stable life and cutting quality is provided with cutting stainless steels due to the coating effect. -
Circular saw blade suitable for cutting stainless steel materials.
Edge material specifications
Uses carbide tips with high toughness.Target materials
Minimized adhesion of chips to prevent tooth chipping caused by chip inclusion with cutting stainless steels. -
Titanium-coated circular saw blade with excellent wear resistance.
Edge material specifications
Carbide tips with high toughness is coated original.Target materials
Both chipping resistance and wear resistance, stable life and cutting quality is provided with cutting structural carbon steels, structural alloy steels, pipes and special steel (except for stainless steels and heat-resisting steels). -
Circular saw blade suitable for cutting general mild steel materials.
Edge material specifications
Uses cermet tips with excellent wear resistance and deposition resistance.Target materials
Excellent in chipping resistance and suited for cutting a wide range of materials such as structural carbon steels, structural alloy steels and pipes. -
Circular saw blade suitable for cutting general mild steel materials such as structural steel.
Edge material specifications
Uses cermet tips with excellent wear resistance and deposition resistance.Target materials
Stable life and cutting quality is provided with cutting structural carbon steels and structural alloy steels up to C ≤ 0.45%. -
Thick blade capable of cutting a curved contour under harsh cutting conditions.
Developed for auto contour curve cutting under harsh cutting conditions
This model is the thicker version of A.
It features AMADA’s unique tooth profile design with a 5˚ positive rake angle in the same fashion as A. Long-lasting excellent sharp cutting is ensured. -
Versatile carbon contour blade available in different sizes.
Versatile contour blade with the longest history and heritageThis is a contour blade made of AMADA’s original material with special heat treatment.
This model has a much wider variety of sizes compared to other manufacturers’ products.
It is suitable for not only metal materials but also lumber and plastic materials. -
Bi-metal contour blade made of high speed steel and designed for cutting difficult-to-cut materials.
Bi-metal blade developed for contour machines
“No breakage, no bend and long-lasting sharp cutting” – three requisites essential to blades for contour cutting of various steel materials
AMADA’s original tungsten high speed steel for the blade teeth and tough special spring steel for the blade body
-
Blade suitable for cutting general steel, cast iron and nonferrous metal materials with small diameters
Blade body with improved fatigue strength.Blade tooth tips made of AMADA’s original special alloy tool steel
AMADA’s proprietary heat treatment technology for improving the fatigue strength of the blade body
Suitable for cutting materials with small diameters, such as general steel, cast iron, nonferrous metal and tool steel materials that may cause a high degree of cutting resistance
-
Blade suitable for cutting general steel, cast iron and nonferrous metal materials with small diameters.
Blade tooth tips made of AMADA’s original special alloy tool steel
AMADA’s proprietary heat treatment technology to give unparalleled toughness and hardness to carbon blades
Suitable for cutting general steel, cast iron and nonferrous metal materials with small diameters
Bandsaws, Circular Saws, and Sawing Machines
We provide high-quality bandsaw machines from Amada, a Japan manufacturer. They also provide Circular Saws and Sawing machines.
-
Integrated console
The operation panel is no longer located in a moving area but is integrated with the control panel, which allows a user to remotely control main functions.
The integrated construction further increases electrical maintainability.PF valve
The cutting process can be optimized just by setting up the PF valve to the target “material, shape and size”.
Availability of wide blades (optional)
Selecting a wider blade can further increase cutting speed.
HA-250:Blade width increased from 27mm to 34mm
HA-400:Blade width increased from 34mm to 41mm -
Integrated console
The operation panel is no longer located in a moving area but is integrated with the control panel, which allows a user to remotely control main functions.
The integrated construction further increases electrical maintainability.NC programming function
This function allows a user to program a cutting method and the number of pieces as desired. The maximum 99 patterns can be programmed.
The embedded self-diagnosis function will indicate an error code if a trouble is detected.Proximal light
This light is helpful for proper operation in the area close to the blade.
Automatic end positioning
CNC-controlled band saw’s popular function is available as an optional function to eliminate the need of hassle scale matching work on the shop floor.Availability of wide blades (optional)
Selecting a wider blade can further increase cutting speed.
HFA-250:Blade width increased from 27mm to 34mm
HFA-400:Blade width increased from 34mm to 41mm -
Automatic sizing cut for forged large materials
Major change made to a conventional automatic feeder allows for automatic sizing cut for forged large materials (materials having an uneven surface).
PF valve
The cutting process can be optimized just by setting up the PF valve to the target “material, shape and size”.
NC programming function
This function allows a user to program a cutting method and the number of pieces as desired. The maximum 99 patterns can be programmed.
The embedded self-diagnosis function will indicate an error code if a trouble is detected.Full stroke vise
A full stroke type of vise cylinder was introduced to allow for clamping just by pressing a single button regardless of a change in material width. -
-
Band saw machine compatible with AXCELA blade
This band saw machine model offers the same basic specifications and operability as PCSAW-430X/530X except that this CNC-controlled band saw machine model is compatible with cutting the conditions of the AXCELA blade and can maximize the capability and performance of the AXCELA high performance carbide blade.
Tooth tip protection
The material relief function is available as a standard function to prevent the interference of teeth tips with a target cut surface. For the purpose of preventing tooth chipping, this function commands the feed vise to give a rearward relief to a material when the blade is lifted upon completion of the cutting process.
High speed cutting
High speed cutting is assured by a combination of lower cutting resistance achieved by the pulse cutting technology and high rigidity frame constructed with the double column guide.
Cutting feed controlled by servo motor
Cutting feed controlled by a servo motor allows for precise, powerful cutting at a high cutting rate.
High-power blade motor
The powerful blade motor yields a higher cutting rate.
For higher power output, PCSAW-430AX and PCSAW-530AX are driven by 11kW and 15kW high power blade motors respectively.Back gauge function
Our back gauge function built in this model has gained popularity among users. The feeding vise can be used as a back gauge for facilitating the cutting of remnants to produce shorter products. This model is designed to cut up to 95mm or 35mm with the optional back gauge jig.
-
Middle blade guide
The world’s first middle blade guide eliminates blade chattering during the cutting of wide materials.
Minimizes blade deviation.10° inclined blade
The shortest possible cutting length of the blade for wide material cutting underpins high speed cutting without any load on the blade.
Movable front vise
The front vise can travel 240mm and go in over the blade, which facilitate cut alignment and remnant ejection.
Stand type operation panel
The swivel stand type operation panel further increases workability and operability in the cut alignment stage.
Chip conveyor
A large-diameter chip conveyor is installed as a standard component to improve the work environment. -
High speed cutting
The pulse cutting technology reduces cutting resistance thereby minimizing blade teeth wear and increasing cutting rates.
High rigid structure
The post type construction gives higher rigidity than the hinge type.
Full cover
The introduction of full cover design prevents scattering of chips and cutting oil to ensure a better work environment.
SMARTCUT BAND as a standard equipment
Environment-friendly SMARTCUT BAND installed as a standard blade helps to increase yield and reduce chips produced. -
Integrated console
The operation panel is no longer located in a moving area but is integrated with the control panel, which allows a user to remotely control main functions.
The integrated construction further increases electrical maintainability.NC programming function
This function allows a user to program a cutting method and the number of pieces as desired. The maximum 99 patterns can be programmed.
The embedded self-diagnosis function will indicate an error code if a trouble is detected.Proximal light
This light is helpful for proper operation in the area close to the blade.
Automatic end positioning
CNC-controlled band saw’s popular function is available as an optional function to eliminate the need of hassle scale matching work on the shop floor.
High-rigidity construction
The post type construction gives higher rigidity than the hinge type. -
Extra large metal cutting machine
Extra large band saw models H-1300II, H-1600II and H-2116II are capable of cutting φ1300 or 1300 square, φ1600 or 1600 square and φ1600 or 2100 wide x 1600 high respectively.
Cutting performance covering all types of large materials
A bi-metal extra wide blade (SGLB or MAGNUM) is used, which easily cuts large materials and difficult-to-cut materials. Variable blade speed allows a user to select desired blade speed as required for materials ranging from regular steel materials to difficult-to-cut materials.
High rigidity construction
A clamping force of the powerful hydraulic wide vise can cover round, square and irregularly-shaped materials. The maximum loading masses of the models are 24000kg, 40000kg and 40000kg respectively with a large table.
Cutting speed monitoring and cutting depth setting unit
Cutting speed can be quickly observed through the digital counter.
Feed table used to feed materials
Materials are fed by the 180mm stroke table.
-
A hyper-speed band saw machine created through the integrated development of machines and blades
Production efficiency is dramatically improved by shortening the cutting time.
We have newly designed a “double gates type guide” and a “bridge type saw head frame” to realize stable high-speed cutting of mild steel.
Mass cutting at the fastest speed in its class. We have developed an epoch-making bandsaw that overturns common sense. -
PF valve
The cutting process can be optimized just by setting up the PF valve to the target “material, shape and size”.
Lever type insert clamp
A foolproof lever type insert clamp is installed to the guide bracket.
Motor-driven Coolant pump
A motor-driven centrifugal pump was introduced in this model, rather than a conventional gear pump. Cutting fluid can be used and cleaned regardless of whether the main motor is ON or OFF.
Sizing stopper
The effective use of the sizing stopper can reduce workload in cutting multiple materials.
-
The optical fiber itself is transparent and does not emit light. It emits light through its both ends and LED spotlights.
Featured Products
-
Ideal for tube end curling!
EXP_FB The “Tube Expanders FB” are rolling type tube expansion tools used for fixing tubes to tube sheets during the manufacturing process for heat exchangers.
Since it can perform parallel tube expansion and curling simultaneously, processing time can be greatly reduced.
Special five-roller type
-
OSD Series Hydraulic Torque Wrenches
FEATURES
One-piece Forming Machine body made of aluminum titanium alloy, high strength, high tenacity and design to exert torque on toughest for a smaller operating radius.
Orbit-X hydraulic torque wrenches are one of the most advanced tools in the industry. Some of the features of Orbit-X hydraulic torque wrenches are as below: Accuracy in repeatability, Very few moving parts, Fast stoke & designed to fit each application. Orbit-X manufactures two series of Hydraulrenches as fic Torque Wollows: -
Cut off tube protrusion easily!
The “Facing Tool” is a tube end facing tool for keeping tube protrusion uniform.
Two types of cutters are available depending on the tube end shapes, one for flat surfaces and the other for round surfaces. -
Orbit-X Electric Torque Wrenches are operated by inbuilt Electric geared motor (single phase). Torque can be pre-set within the torque range provided by the model the pre-set torque gets delivered on the nut. Orbit-X has variety of Electric Torque Wrenches for various Square drive sizes, RPM & Torque.
-
Product Features
High strength, Heat treated alloy steel body for better life.
Hard chrome plated ram to resist scoring and corrosion.
Single acting load return. Precise machined body for smooth operation.
Wiper to arrest ingress of foreign particles.
Easy adjustable toe fixing positions for different heights and strokes.
Grooved toe to avoid load slippage.
Custom strokes available on request.
High pressure long life seals. QCC with Plastic dust cap. Aluminium Dust Cap on Request.
Advantage to use single or multiple jack with common pump.
Adjustable legs for extra grip. Castor wheels for easy mobility in new version.
Port size 3/8th inch NPT. -
Fully automatic tube end facing!
The “Power Facer” is a pneumatic, tube end facing tool for finishing the ends of tubing into various shapes during the manufacturing process for heat exchangers.
Just press the switch to perform tube end finishing. There is no reaction force involved in the process, significantly reducing worker fatigue. -
Future Technologies with Amada
With more than 70 years of industry experience, comprehensive global manufacturer of metalworking machinery, AMADA contributes to the development of manufacturing considering what is most necessary from the customer’s point of view.
Our Brands
